How to Replace the HP Pavilion G6T-2000 G6T-2200 Series Keyboard

Use the steps in this section to replace the HP Pavilion G6T-2000 G6T-2200 Series keyboard.

Step 1

 Position the keyboard upside down so you have access to the ribbon cable and the connector.

Step 2

 Insert the keyboard ribbon cable into the ZIF connector.
CAUTION:Use care to prevent damaging the ZIF connector and ribbon cable.

Step 3

 Push the locking bar down to secure the ribbon cable in the connector.

Step 4

 Turn the keyboard over and place the tabs on the bottom edge of the keyboard into the top cover Rotating the keyboard back into place

Step 5

 Lower the keyboard into position and press along the edges of the keyboard to secure it to the computer.

Step 6

 Close the display panel, turn the computer upside down, and replace the screw that secures the keyboard to the base.

Step 7

 Replace the CD/DVD drive.

Step 8

Replace the service cover.

Step 9

Replace the battery.

How to Remove HP Pavilion G6-2000 G6-2200 Laptop Keyboard

How to Remove HP Pavilion G6-2000 G6-2200 Series Laptop Keyboard, Follow the steps in this section to remove the keyboard.

Step 1

Remove the battery.

Step 2

Remove the service cover.

Step 3

Remove the CD/DVD drive.

Step 4

Remove the Phillips head screw (identified with a keyboard icon) that secures the HP Pavilion G6-2000 G6-2200 keyboard to the computer. Save the screw for keyboard replacement.

Step 5

Open the display panel and position the computer on its side.

Step 6

While supporting the notebook, gently press the exposed area of the keyboard in the keyboard release cut out to partially release it from the top cover.

Step 7

 Turn the computer right side up and open all the way.

Step 8

 Lift the rear edge of the keyboard and rotate the keyboard toward the front of the notebook until you have access to the keyboard ribbon cable and ZIF connector.

Step 9

 Gently lift the locking bar on the keyboard ZIF connector and remove the keyboard ribbon cable.


CAUTION:Use care to prevent damaging the ZIF connector and ribbon cable.

Step 10

Remove the keyboard.

How to removal and installation Lenovo ThinkPad T410, T410i Keyboard

Lenovo ThinkPad T410, T410i Keyboard removal instructions:

For access, remove this FRUs in order:

Push down the Lenovo ThinkPad T410, T410i keyboard a little toward the arrow [2] to detach the front edge of the keyboard from the frame.

Lift the keyboard a little in the direction shown by arrow [3], and then detach the connector [4].

Lenovo ThinkPad T410, T410i Keyboard installation instructions:

Attach the keyboard connector.

Attach the keyboard so that the keyboard edges [a] are under the frame as shown in this figure.

To make sure that the front edge of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you.

Make sure that front edge of the keyboard [b] is attached firmly.

Secure the keyboard by tightening the screws from the bottom side of the computer.

How to Remove Replace and Install Your HP Mini 210 Laptop Heatsink Fan

1. Inorder to replace fix or install your new HP  mini 210-1000 laptop fan and heatsink, you will need to open up your laptop. You can do this by removing the screws from the bottom of the laptop.

2. Once the screws have been removed from the bottom of your laptop, you can now remove the HP mini 210-1000 laptop keyboard and plastic bezels from your HP mini 210 laptop.

3. You will see your HP mini 210-3000 Fan and Heat Skin exposed.

4. Use a screw drivers and remove the screws from you HP mini 210 HeatSin Fan.

5. Before reinstalling the new HP mini 210 Fan onto your laptop, you can clean the HP mini 210 Fan. To clean your Fan and Heatsink, use a can of air and blow out any dirk from your HP mini 210 Fan. You can also use a paint brush to clean out the dirt from the hard to get areas. Somtimes cleaning your HP mini 210 laptop fan will actually repair it. Dirt can cause the HP mini 210 Laptop Fan to make noise and even stop spinning properly.

How to Remove Replace and Install Your Lenovo ideapad U450 Laptop Keyboard

1. View the back of your Lenovo U450 laptop. If the laptop keyboard has screw holes, then you now you need to remove screws from the bottom base of your plastic bezel. If the keyboard does not have any screw holes, then screws are usually not required to be removed from the bottom of the laptop.

2. Now that you have determined if screws are required to be removed from your Lenovo U450 laptop keyboard, we will now pry the keyboard out using a thin object. The first step is to view the top of the keyboard area, also known as the keyboard plastic bezel. If your keyboard has a plastic bezel above your keyboard, you will need to pry it out. If you don’t have a plastic bezel above your keyboard, then you can take a think object. Place the thin object between your Lenovo U450 laptop keyboard and the plastic bezel, and pry out the keyboard.

3. Now that your Lenovo U450 keyboard has been removed your will need to disconnect the Lenovo U450 keyboard cable ribbon from the motherboard. There is usually pins connected to the Lenovo U450 motherboard that need to be pushed up/down. Once the keyboard connector cable has been removed from the Lenovo U450 laptop keyboard, remove the keyboard.

4. We will now install your new Lenovo U450 laptop keyboard.

5. Reconnect the Lenovo U450 keyboard to the motherboard. Insert the Lenovo U450 Keyboard back into the motherboard. Secure the pins and push the pins in. Once your keyboard is secured, you can now aligned the keyboard with the grooves. Push the keyboard down and in place. If there is a Lenovo U450 plastic keyboard bezel, place it back in place. Secure all your Lenovo U450 laptop screws back in place.

6. That’s all, you just installed your replacement notebook keyboard!

Other lenovo ideapad u450 laptop part: lenovo ideapad u450 laptop screen hinges

Lenovo Ideapad Y570 series laptop complete disassembly

If you don’t have the experience on disassembly the Lenovo Ideapad Y570 laptop, we suggest you refer to the official maintenance manual firstly if you have. Here we provide a universal instruction for the reference, some steps may be not the same. If you need a detailed guide or manual, please visit below link:
http://www.youtube.com/watch?v=7tE_i91q5vw

1. Please turn off your Lenovo Ideapad Y570 laptop, disconnect the power adapter and remove the battery.

2. Turn the laptop over. Remove the screws (may not exist) that hold the Lenovo Ideapad Y570 hinges on the back of the computer.

3. Remove all the screws (may not exist) that hold the keyboard and keyboard bezel in place, then gently pry keyboard bezel using a flat head screwdriver. Lift the keyboard and unplug the keyboard cable from the motherboard to remove the keyboard. 

4. Detach both hinge covers using your fingers. Unscrew the screws securing the Lenovo Ideapad Y570 hinges to the laptop base.

5. Locate the screws on the LCD, pry the rubber screw seals using a flat-head screwdriver. Unscrew the screws attached under the seals. Remove the screen bezel. 

6. Remove the screws securing the hinges d to the Lenovo Ideapad Y570 LCD. 

7. Now, you can remove the old Lenovo Ideapad Y570 Hinges by sliding them out. Insert the new hinges in their correct place. Reverse the above procedure to assemble the laptop. 

We supply high quality and low price lenovo ideapad y570 laptop part:
lenovo ideapad y570 keyboard
lenovo ideapad y570 cpu cooling fan
lenovo ideapad y570 screen hinges