How to Install Samsung NC10 Series Laptop CPU Cooling Fan

How to Install Samsung NC10 Series Laptop CPU Cooling Fan

1. In order to install the new Samsung NC10 laptop heatsink fan, you will need to open up your laptop. You can do this by removing the screws from the bottom of the laptop.

2. Once the screws have been removed from the bottom of your laptop, you can now remove the samsung nc10 keyboard and plastic bezels from your Samsung NC10 series laptop.

3. You will see your Samsung NC10 Fan and Heat Skin exposed.

4. Use a screw drivers and remove the screws from you Samsung NC10 HeatSink Fan.

5. Before reinstalling the new Samsung NC10 Fan onto your laptop, you can clean the Samsung NC10 Fan. To clean your Fan and Heatsink, use a can of air and blow out any dirk from your Samsung NC10 Fan. You can also use a paint brush to clean out the dirt from the hard to get areas. Somtimes cleaning your Samsung NC10 laptop fan will actually repair it. Dirt can cause the Samsung NC10 Laptop Fan to make noise and even stop spinning properly.

How to Install Toshiba Satellite L500 series laptop keyboard

In the following guide I'll be taking apart and removing the motherboard from a Toshiba Satellite L500 laptop. Also, this guide should for for one of the following Toshiba models: Satellite L505, Satellite L505D, Satellite L500, Satellite L500D.

STEP 1
First of all, turn off the laptop and remove the battery.
Using a sharp object carefully lift up the plastic bezel above the keyboard.

STEP 2
Remove the keyboard bezel.

STEP 3
Remove four screws securing the Toshiba Satellite L500 keyboard to the laptop.

STEP 4
Carefully lift up the keyboard from the laptop.

STEP 5
Access the keyboard cable connector located under the keyboard.
You have to unlock the connector and release the cable before removing the keyboard.

STEP 6
In order to unlock the keyboard cable connector move the locking clip towards the LCD screen.
Move it only about 2 millimeters. The locking clip must stay attached to the connector base.

Warning! If you break the connector, you'll have to replace the motherboard.

Reverse the produce to install Toshiba Satellite L500 series laptop keyboard.

How to Replace the HP Pavilion G6T-2000 G6T-2200 Series Keyboard

Use the steps in this section to replace the HP Pavilion G6T-2000 G6T-2200 Series keyboard.

Step 1

 Position the keyboard upside down so you have access to the ribbon cable and the connector.

Step 2

 Insert the keyboard ribbon cable into the ZIF connector.
CAUTION:Use care to prevent damaging the ZIF connector and ribbon cable.

Step 3

 Push the locking bar down to secure the ribbon cable in the connector.

Step 4

 Turn the keyboard over and place the tabs on the bottom edge of the keyboard into the top cover Rotating the keyboard back into place

Step 5

 Lower the keyboard into position and press along the edges of the keyboard to secure it to the computer.

Step 6

 Close the display panel, turn the computer upside down, and replace the screw that secures the keyboard to the base.

Step 7

 Replace the CD/DVD drive.

Step 8

Replace the service cover.

Step 9

Replace the battery.

How to Remove HP Pavilion G6-2000 G6-2200 Laptop Keyboard

How to Remove HP Pavilion G6-2000 G6-2200 Series Laptop Keyboard, Follow the steps in this section to remove the keyboard.

Step 1

Remove the battery.

Step 2

Remove the service cover.

Step 3

Remove the CD/DVD drive.

Step 4

Remove the Phillips head screw (identified with a keyboard icon) that secures the HP Pavilion G6-2000 G6-2200 keyboard to the computer. Save the screw for keyboard replacement.

Step 5

Open the display panel and position the computer on its side.

Step 6

While supporting the notebook, gently press the exposed area of the keyboard in the keyboard release cut out to partially release it from the top cover.

Step 7

 Turn the computer right side up and open all the way.

Step 8

 Lift the rear edge of the keyboard and rotate the keyboard toward the front of the notebook until you have access to the keyboard ribbon cable and ZIF connector.

Step 9

 Gently lift the locking bar on the keyboard ZIF connector and remove the keyboard ribbon cable.


CAUTION:Use care to prevent damaging the ZIF connector and ribbon cable.

Step 10

Remove the keyboard.

How to removal and installation Lenovo ThinkPad T410, T410i Keyboard

Lenovo ThinkPad T410, T410i Keyboard removal instructions:

For access, remove this FRUs in order:

Push down the Lenovo ThinkPad T410, T410i keyboard a little toward the arrow [2] to detach the front edge of the keyboard from the frame.

Lift the keyboard a little in the direction shown by arrow [3], and then detach the connector [4].

Lenovo ThinkPad T410, T410i Keyboard installation instructions:

Attach the keyboard connector.

Attach the keyboard so that the keyboard edges [a] are under the frame as shown in this figure.

To make sure that the front edge of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you.

Make sure that front edge of the keyboard [b] is attached firmly.

Secure the keyboard by tightening the screws from the bottom side of the computer.

How to Remove Replace and Install Your HP Mini 210 Laptop Heatsink Fan

1. Inorder to replace fix or install your new HP  mini 210-1000 laptop fan and heatsink, you will need to open up your laptop. You can do this by removing the screws from the bottom of the laptop.

2. Once the screws have been removed from the bottom of your laptop, you can now remove the HP mini 210-1000 laptop keyboard and plastic bezels from your HP mini 210 laptop.

3. You will see your HP mini 210-3000 Fan and Heat Skin exposed.

4. Use a screw drivers and remove the screws from you HP mini 210 HeatSin Fan.

5. Before reinstalling the new HP mini 210 Fan onto your laptop, you can clean the HP mini 210 Fan. To clean your Fan and Heatsink, use a can of air and blow out any dirk from your HP mini 210 Fan. You can also use a paint brush to clean out the dirt from the hard to get areas. Somtimes cleaning your HP mini 210 laptop fan will actually repair it. Dirt can cause the HP mini 210 Laptop Fan to make noise and even stop spinning properly.

How to Remove Replace and Install Your Lenovo ideapad U450 Laptop Keyboard

1. View the back of your Lenovo U450 laptop. If the laptop keyboard has screw holes, then you now you need to remove screws from the bottom base of your plastic bezel. If the keyboard does not have any screw holes, then screws are usually not required to be removed from the bottom of the laptop.

2. Now that you have determined if screws are required to be removed from your Lenovo U450 laptop keyboard, we will now pry the keyboard out using a thin object. The first step is to view the top of the keyboard area, also known as the keyboard plastic bezel. If your keyboard has a plastic bezel above your keyboard, you will need to pry it out. If you don’t have a plastic bezel above your keyboard, then you can take a think object. Place the thin object between your Lenovo U450 laptop keyboard and the plastic bezel, and pry out the keyboard.

3. Now that your Lenovo U450 keyboard has been removed your will need to disconnect the Lenovo U450 keyboard cable ribbon from the motherboard. There is usually pins connected to the Lenovo U450 motherboard that need to be pushed up/down. Once the keyboard connector cable has been removed from the Lenovo U450 laptop keyboard, remove the keyboard.

4. We will now install your new Lenovo U450 laptop keyboard.

5. Reconnect the Lenovo U450 keyboard to the motherboard. Insert the Lenovo U450 Keyboard back into the motherboard. Secure the pins and push the pins in. Once your keyboard is secured, you can now aligned the keyboard with the grooves. Push the keyboard down and in place. If there is a Lenovo U450 plastic keyboard bezel, place it back in place. Secure all your Lenovo U450 laptop screws back in place.

6. That’s all, you just installed your replacement notebook keyboard!

Other lenovo ideapad u450 laptop part: lenovo ideapad u450 laptop screen hinges

Lenovo Ideapad Y570 series laptop complete disassembly

If you don’t have the experience on disassembly the Lenovo Ideapad Y570 laptop, we suggest you refer to the official maintenance manual firstly if you have. Here we provide a universal instruction for the reference, some steps may be not the same. If you need a detailed guide or manual, please visit below link:
http://www.youtube.com/watch?v=7tE_i91q5vw

1. Please turn off your Lenovo Ideapad Y570 laptop, disconnect the power adapter and remove the battery.

2. Turn the laptop over. Remove the screws (may not exist) that hold the Lenovo Ideapad Y570 hinges on the back of the computer.

3. Remove all the screws (may not exist) that hold the keyboard and keyboard bezel in place, then gently pry keyboard bezel using a flat head screwdriver. Lift the keyboard and unplug the keyboard cable from the motherboard to remove the keyboard. 

4. Detach both hinge covers using your fingers. Unscrew the screws securing the Lenovo Ideapad Y570 hinges to the laptop base.

5. Locate the screws on the LCD, pry the rubber screw seals using a flat-head screwdriver. Unscrew the screws attached under the seals. Remove the screen bezel. 

6. Remove the screws securing the hinges d to the Lenovo Ideapad Y570 LCD. 

7. Now, you can remove the old Lenovo Ideapad Y570 Hinges by sliding them out. Insert the new hinges in their correct place. Reverse the above procedure to assemble the laptop. 

We supply high quality and low price lenovo ideapad y570 laptop part:
lenovo ideapad y570 keyboard
lenovo ideapad y570 cpu cooling fan
lenovo ideapad y570 screen hinges

Removing and Replacing the HP Compaq 8510p 8510w Notebook PC Keyboard

HP Compaq 8510p 8510w Notebook PC Keyboard removal

Review the safety considerations before performing the steps listed below:

Before you begin
Put on your electrostatic discharge (ESD) wrist strap to avoid damaging any circuitry.
Remove all devices (such as diskettes and CD-ROMs) from the computer.
Power off the computer and any peripheral devices that are connected to it.
Disconnect the power cord from the electrical outlet and then from the computer. When the computer is plugged into an AC power source, there is always voltage applied to the system board. You must disconnect the power cord from the power source before opening the computer to prevent system board or component damage.
Disconnect all peripheral device cables from the computer.

Static electricity
Static electricity can damage electrical components. Before removing or replacing a component, touch a grounded metal object to discharge static electricity. Also observe the following precautions to prevent damage to electric components and accessories:

To avoid hand contact, transport products in static-safe containers such as tubes, bags, or boxes.
Protect all electrostatic parts and assemblies with conductive or approved containers or packaging.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations.
Place items on a grounded surface before removing them from their container.
Always be properly grounded when touching a sensitive component or assembly.
Avoid contact with pins, leads, or circuitry.
Place reusable electrostatic-sensitive parts from assemblies in protective packaging or conductive foam.

Disassembly
During disassembly, label each cable as you remove it, noting its position and routing. This will make the replacement of the cables much easier, and will ensure that the cables are rerouted properly to protect the cables.
Keep all screws with the units removed. The screws used in the computer are of different thread sizes and lengths; using the wrong screw in a component could damage the unit.

Remove the battery.

Loosen the two captive P1 Phillips-head screws that secure the HP Compaq 8510p 8510w Notebook PC keyboard to the base enclosure.

Turn the notebook right side up and open the display panel fully.

Slide the four plastic locking tabs toward the bottom edge of the keyboard to unlock the keyboard from the switch cover.
Use a flat-bladed tool or your finger to lift the top edge of the keyboard and then place it upside down on the top cover.
Using minimal force, lift the locking bar to unlock the keyboard ZIF connector on the system board.

Remove the keyboard ribbon cable from the ZIF connector.
Using minimal force, lift the locking bar to unlock the pointing stick ZIF connector on the system board (only on models with a pointing stick).

Remove the pointing stick ribbon cable from the ZIF connector and remove the keyboard.

HP Compaq 8510p 8510w Notebook PC Keyboard replacement

Place the HP Compaq 8510p 8510w Notebook PC keyboard upside down on the top cover.
Insert the pointing stick ribbon cable into the pointing stick ZIF connector on the system board (only on models with a pointing stick).

Push the locking bar down to lock the pointing stick ZIF connector on the system board.
Insert the keyboard ribbon cable into the keyboard ZIF connector on the system board.

Push the locking bar down to lock the keyboard ZIF connector on the system board.
Toe the tabs on the bottom edge of the keyboard into the top cover.
Press the keyboard flat and slide the four plastic locking tabs toward the rear of the notebook to lock the keyboard to the switch cover.
Close the display panel and turn the notebook upside down.
Tighten the two captive P1 Phillips-head screws that secure the keyboard to the base enclosure.

How to Replace Lenovo Ideapad G570 Series Laptop Screen

At some point in your lifetime, you'll probably end up in this situation: You own a perfectly good laptop, but you've broken the screen! By utilizing this guide, you can save yourself time and money while learning more about your computer! This guide will explain, step-by-step, how to replace the screen in your Lenovo G570 notebook computer.

Step 1
Before working on your laptop, check the warranty terms. If the machine is still under warranty, working on it yourself may void the warranty.

Step 2 — Prepare Your Workspace...
Gather the necessary tools, and make sure you have a large open space (such as a workbench) to work on.

Step 3
Remove the 2 rubber bumpers which cover the screws. (They are located on the bottom left and right corners of the bezel.)

Step 4
Remove the front plastic bezel from the screen using the following steps.
Pry up the bezel in the location depicted with a plastic opening tool or small flat-head screwdriver until you free the first few retaining clips.
Once a few clips are loosened, you can pry the bezel the rest of the way off by hand.

To do so, pull each side of the bezel outward and towards the center of the screen, until all of the retaining clips have been released.

Step 5
Remove the four screws (one in each corner) which attach the screen to the lid.

Step 6
Carefully pull the lid away from the screen, while keeping in mind that there are cables attached to the lid as well as the screen.
The lid will separate from the screen, but the cables will not. Lean it against something to avoid stressing the cables.

Step 7
Now, detach the lenovo ideapad g570 video cable from the back of the screen.
Proceed with caution, as the video cable is very easily damaged!

Step 8
Remove the 8 screws (4 on each side) which attach the lenovo idepad g570 hinges to the screen

Step 9
Remove the screen, and recycle it at your local dump or recycling center

Step 10 — Time to replace the screen!
Before you begin, be sure to put something on the lenovo ideapad g570 keyboard to protect the screen from being scratched

Step 11
Position the screen face-down on the keyboard, and line up the hinges with the holes on either side of the screen
Using your Philips-head screwdriver, replace the 8 screws (4 on each side)

Step 12
Connect the video cable!
Be careful not to damage the cable, or to touch the base of the circuit board on the monitor

Step 13
Lift the plastic lid up to the back of the screen, and press them together so that lid now hinges with the screen
Be careful that the cables which run along the bottom inside edge of the lid are not squished by the screen when you bring the screen and lid together!

Step 14
Replace the four screws that hold the screen and lid together
Snap the plastic bezel on, and replace the two screws which connect the bezel to the computer (reference step 4 for clarification)

How to Remove Replace Install your Toshiba Satellite A350 Laptop LCD Screen

1. Remove the rubber covers from you Toshiba Satellite A350 LCD Screen.

2. Use a philips head screw driver to remove the screws.

3. Pry off the Toshiba Satellite A350 Plastic LCD bezel.

4. Remove the screws from the side of the LCD hinges.

5. Handle the Toshiba Satellite A350 LCD hinges with care as they are delicate.

6. Place the Toshiba Satellite A350 LCD Screen down on its front and remove the LCD ribbon cable from the LCD.

7. Unplug and remove the Toshiba Satellite A350 Inverter from the LCD.

8. You are now ready to replace and install your new Toshiba Satellite A350 LCD Screen.

9. Recconnect back your Toshiba Satellite A350 Inverter LCD Cable and Hinges.

10. Place the screws back in and secure the Plastic LCD Bezel back in place.

How to Adjust Asus G73 CPU Cooling Fan Speed

A laptop is a preferred choice for computing needs by many people, as it provides flexibility and mobility. Students, company employees and homemakers use laptops to study, do their work and pay their bills respectively. Just like desktops, laptops have maintenance needs and addressing them can make the laptop function better. One of the needs that come up from time to time is adjusting the Asus G73 cpu cooling Fan speed; here are some tips to do so.

1. Check your laptop make and model and research how to adjust the Asus G73 CPU cooling fan speed that is specific to the brand. There is not one universal way to do this, so finding the exact model will help you do your research. Some brands have tips written in the user's manual.

2. Check in your laptop's BIOS (Basic Input/Output System) to see if the Asus G73 CPU fan speed is available. The BIOS provides an interface for a computer's hardware and software. This is where you can find the basic settings of the computer. You can go to the BIOS by doing a shutdown and upon restarting your computer, hitting F10 on your keyboard (F key and the number 10 key). You can change the settings from there by toggling the dropdown menu or prompt. Once done, go ahead and hit "Save."

3. Check if there is a chipset driver for a fan installed on your laptop. If there is one, you can adjust the Asus G73 CPU fan speed from there. The chipset is what controls the fan, network adapters, sound and video controllers depending what is on your chipset. You can find chipsets on your computer's motherboard.

4. Download the software to adjust fan speed if you cannot adjust it from your computer's BIOS. There is some software available for download, such "Speedfan." The software allows you to follow steps to adjust the speed of your Asus G73 CPU fan. Before purchasing the software, check first if it is compatible with your laptop. Get your laptop specs and contact the software maker's customer or technical support to find out if it will work for your laptop. Once they confirm, you may then proceed with buying and downloading the software.

5. Use the software carefully. Your laptop manufacturer may not support the software you are purchasing; therefore, you will use it at your own risk. If using the program negatively affects your laptop's performance, and you send it in for repairs, the manufacturer's warranty may not cover it if they discover that the software caused the problem.

6. Download CoreDuoTemp or smcFanControl to adjust the Asus G73 Fan speed of an Apple laptop such as the MacBook. Both of them will allow you to monitor and control the speed of your fan as well as the temperature.

7. Adjust the RPM (revolutions per minute) of your active Asus G73 Fan speed by sliding the mark to the right. You can also adjust the temperature this way.

8. Call your manufacturer's technical support to walk you through adjusting the fan speed settings. They should know what to do and what to avoid depending on the symptoms. If they cannot do it over the phone, they can send someone to you or they can ask you to send your laptop for adjustment of Asus G73 Fan speed.

How to Replace the Laptop Keyboard?

Enusre the laptop is fully powered off, unplugged from the wall, and the battery taken out.
Turn the laptop over. On some models icons indicating which screws are attached to the keyboard are displayed. If not, you may have to "eyeball" it if you can't find a breakdown for your model online.

Remove those screws with a T-8 or Phillips screwdriver.

Turn the laptop back over and open it up. Check and see if the keyboard is tucked under any plastic pieces. If so, find if those plastic pieces are screwed into anything, and unfasten them as well. If not, it probably uses clamps that can easily be removed.

Remove the plastic pieces carefully with a toothpick or plastic pick if there is any in the way.

Unscrew any screws at the top (if necessary) and remove the keyboard itself from top to bottom. You'll notice that the keyboard is connected with a thin, but wide, data cable to the system board at the bottom.

Take that same pick and lift the plastic connectors that hold in this data cable in place.

Carefully remove the data cable. Now the whole keyboard should be free.

Take the new keyboard out of the plastic, and slip the data cable back in between the plastic connectors on the system board. Make sure it's all the way in.

Use the pick to push the plastic connectors back into place, and make sure it's holding the data cable in.

Slip the keyboard itself into place, from bottom to top. Make sure the screw holes or clamps line up at the top.

Refasten the keyboard in place at the top.If you had to remove any plastic pieces, carefully snap them back in and replace any screws you had to remove.

Turn the laptop over and replace all of the keyboard screws.

Finally, put the battery back in and power on the laptop. If all has gone well, the keyboard should be functioning like brand new.

How to Remove Replace and Install Your Samsung R520 R522 Series Laptop Keyboard

1. View the back of your Samsung R520 R522 Keyboard. If the laptop keyboard has screw holes, then you now you need to remove screws from the bottom base of your plastic bezel. If the keyboard does not have any screw holes, then screws are usually not required to be removed from the bottom of the laptop. Turn off your Samsung R520 R522 laptop. Disconnect the AC adapter and remove the Samsung R520 R522 battery.

2. Now that you have determined if screws are required to be removed from your Samsung R522 laptop keyboard, we will now pry the keyboard out using a thin object. The first step is to view the top of the keyboard area, also known as the keyboard plastic bezel. If your keyboard has a plastic bezel above your keyboard, you will need to pry it out. If you don’t have a plastic bezel above your keyboard, then you can take a think object. Place the thin object between your Samsung R520 R522 laptop keyboard and the plastic bezel, and pry out the keyboard.

3. Now that your Samsung R520 R522 keyboard has been removed your will need to disconnect the Samsung R520 R522 keyboard cable ribbon from the motherboard. There is usually pins connected to the Samsung R520 R522 motherboard that need to be pushed up/down. Once the keyboard connector cable has been removed from the Samsung R520 R522 laptop keyboard, remove the keyboard.

4. We will now install your new Samsung R520 R522 laptop keyboard.

5. Reconnect the Samsung R520 R522 keyboard to the motherboard. Insert the Samsung R520 R522 Keyboard back into the motherboard. Secure the pins and push the pins in. Once your keyboard is secured, you can now aligned the keyboard with the grooves. Push the keyboard down and in place. If there is a Samsung R520 R522 plastic keyboard bezel, place it back in place. Secure all your Samsung R520 R522 laptop screws back in place.

6. That’s all, you just installed your replacement notebook keyboard!

Lenovo Thinkpad T430 Keyboard and Touchpad Introduce

The Lenovo Thinkpad T430's keyboard is a departure for Lenovo; they switched to the increasingly popular Chiclet style with extra spacing between the keys. This has the most encouraging tactile feedback out of all the variants I've tried. It has a slightly more clicky sound than the traditional ThinkPad keyboards and the key travel isn't as long, though the feedback doesn't suffer as a result, dare I say it feels even more solid. Lenovo is offering a backlit keyboard courtesy of this new design, a first on a 'real' ThinkPad. It still has the Think Light for die-hard fans, though.

So what's the matter with it? Simply put, more than a few ThinkPad owners will say Lenovo botched the keyboard layout. The Home, End, PgUp, PgDn, Insert and Delete keys are all over the place instead of being clustered in a nice organized group at the top right. Also missing is the multi-colored keys such as the purple [Enter]. This bothers me in a way; the ThinkPad keyboard formula was exactly what many business users wanted and now they changed it - what was the reasoning? It doesn't make sense to the end user. I'm all for change but this is a step backwards.

The touchpad remains largely unchanged but the dimpled surface is slightly more pronounced. It feels almost too rough at first though I got used to it after a few days. The trackpoint "eraser" head in the center of the keyboard is also unchanged and remains the most intuitive version offered by any brand. The buttons for both the touchpad and the trackpoint are excellent with quiet, supple clicks.

How to Replace Acer Aspire 4740 Series keyboard

In this guide, the actual laptop is Acer Aspire 4740. It should work on these laptops. Acer Aspire 3810, Aspire 4410, Aspire 4736, Aspire 4810 seires and so on. Please notice Acer Aspire 4736 series have two different keyboard. If your keyboard likes the one in the Pic1, this guide is invalid.

First of all, please turn off your Acer Aspire 4740 series laptop, disconnect the power adapter and remove the battery.

1. Open your laptop. The acer aspire 4740 series keyboard was secured by five latches.

2. Disconnect five latches on the acer aspire 4740 series keyboard.

3. Carefully pry loose the Acer Aspire 4740 keyboard and turn it over on the touchpad area.

4. Disconnect the keyboard cable from the main board to remove the Acer Aspire 4740 series keyboard.

Reverse the procedure to install your new Acer Aspire 4740 series keyboard.