Laptop LCD Inverter For ACER Aspire 1600

Laptop LCD Inverter For ACER Aspire 1600 Series
Brand new ACER Aspire 1600 Series Replacement Laptop LCD Inverter with low price. It Compatible the following Part No. and Models
Factory Part Number: IV09117/T, 19.21032.031,48.V0712.021, 19.21064.001, T62I194.12, 19.21030.I71, 19.2130.E92, T62i194.01
Compatible Models: Aspire 1360 Series, Aspire 1400 Series, Aspire 1440 Series, Aspire 1500 Series, Aspire 1520 Series, Aspire 1600 Series, Aspire 1660 Series, Travelmate 2000 Series, TravelMate 2100 series, Travelmate 240 Series, Travelmate 2400 Series, Travelmate 242LC MS2138, Travelmate 243LC MS2138, Travelmate 2500 Series, Travelmate 2600 Series, Travelmate 371TCi MS2130, Travelmate 610 Series, Travelmate 611TXV, Travelmate 612TXV, Travelmate 613TXV, Travelmate C100 Series
An inverter is an electrical or electro-mechanical device that converts direct current (DC) to alternating current (AC); the resulting AC can be at any required voltage and frequency with the use of appropriate transformers, switching, and control circuits.Inverters are commonly used to supply AC power from DC sources such as solar panels or batteries.
Inverters convert low frequency main AC power to a higher frequency for use in induction heating. To do this, AC power is first rectified to provide DC power. The inverter then changes the DC power to high frequency AC power.

DELL Inspiron 1420 Keyborad

New Keyborad for DELL Inspiron 1420 1400 NK750 XPS 1500 M1330
Supply brand new DELL Inspiron 1420 Replacement Laptop Keyboard with low price.
Compatible DELL Inspiron 1420 Part Number and Models
Compatible Code:0NK750, 9J.N9382.201, A071, K071425XX, NK750, NSK-D9201.
Models: Inspiron 1420, Inspiron 1520, Inspiron 1521, Vostro 1400, Vostro 1000, Vostro 1500, XPS M1330
Repair For HP DV9000 laptop hinges Steps( Steps14,15)
Step16
If epoxy is set hard you may now put back the LCD. First take outthe 2 top screws holding the arms to the cover. Put the 2 left & rightside screws into LCD screen. Make sure all the contact points andwebcam, etc are lined up.
Step17
Take LCD bezel and flip over. Then cut the 2 clip contact points offwith a razor, smooth to the bezel. If you did grind down the face ofthe bracket against the hinge edge, when you snap the face bezelback it should close back like new or if you didnt you will have a veryunnoticable gap in side, but will be stronger over long term.
Step18
Put the 3 top screws and the 2 bottom screws back into LCDbezel into the laptop casing, then put the 5 rubber sticky padsback on and you are done. Hope it worked out for you.

Provision Compaq LCD hinges Information for you.
Compaq Presario C300, C500, V5000 Series LCD hinge(15.4" Display) .
Compaq C300 LCD hinge for 407797-001, AM00Z000100, AM00Z000200, AMZIP000500, AMZIP000600

HP ZV5000 ZX5000 ZV6000 LCD Hinges

New Original HP ZV5000, ZV6000, ZX5000 Series 15.4" LCD Hinges
Left & Right Hinge set For 15.4" Display,Brand New
mpatible Code:AMHR631F010, AMHR631J010, HR63 PA 154

Repair For HP DV9000 laptop hinges Steps(10,11,12,13)

step 10

Mix up a small batch of epoxy. (you must mix the 2 parts thouroughlyand work quickly so it dont set or you will not get the proper bonding strength) Smear a good amount of epoxy onto the hinge at the contactpoints and clamp without throwing off the shape of the hinge. Use about3 to 4 mini clamps. Allow about 10 minutes for the epoxy to set. If youare the patient type let it sit longer,cant hurt.

step 11

Now that the epoxy has set remove the clamps on the arm. If you havea center punch mark 2-3 points where you will drill for your pop rivots inthe center of the arm. Push pop rivots from the outside of thehinge arm inwards to LCD.

step 12

You will now haveto drill through the back of the hinge out the bracket the small holes forthe original screws to fit. Then bore the front face of the bracket witha 3/16" bit (unless you have the exact size bit for head to recessso the screws will reach through) Go SLOW! DONT over drill, you do notwant to go into the hinge at all!

step 13

Now grind the bracket so it takes shape with the arm also shearingdown the pop rivots smooth on the LCD side of the arm. Then, althoughI didnt do this on mine because I wanted it to have the most strength,you may want to so the face bezel fits completely closed when yousnap it back on later in step 16. Grind down the top edge of the frontface of the bracket to the top of the hinge.

Repair For HP DV9000 laptop hinges(Continuing)

Repair for the broken HP DV9000 laptop hinges

step 5

Now you must free the tired hinge. Depending on how far trashed yourtop cover mounting points are. Try to unscrew the 4 little phillips headscrews from the hinge (only 3 if you took out the one that was coveredby the rubber screw cover already) If the screws turn and do not comeloose the mounting points on the LCD cover have cracked so just leavethem in for now.
step 6
Push the screen all the way open holding it at the right and left hinges
not to cause any further trauma. If your hinge is to far gone and you
cant move it, you will have to force the hinge with pliers when you remove
it during the next step.

step 7

Now try rotating the left hinge asssembly away from the LCD screentowards the closed position. You may need to use pliers on the hinge torotate it because the torque required is significant and is partially thereason your laptop hinge is broken to begin with. Now that it is in thealmost closed position move the pliers to the outside and work the hingeout from the connection point on the base of the unit. It may be tightso keep at it until you pull it free but trying to not break the arm offthe hinge. Remove off the screws and brass inset fasteners and putinto parts container.

step 8

Now you need to put a bend on the angle bracket. Use a bench viseif you have one or clamp a vise grip to the egde of the bracket, withanother large pliers start the bend, With a hammer bang the bend flat. This is a critical step! The bend must take shape with the hinge! Dontover bend or you will weaken the strength. Also make sure you bendthe hinge in the right direction!

step 9

As you can see my edge was completely separated on the hinge arm. I didnt do this but I recommend that you superglue the join on the armso it will not move and in its original position so when you go to put itback together with the LCD screen it sits correctly in the chassis.Overlay the hinge with your new support bracket. Make marks withblack permanent marker where you need to grind out so it overlaysthe hinge correctly that the bracket sits on top of the hinge. You needto cut the length on the front-face part of the bracket so you dontcover the 3rd hole on the hinge. (I cut it off at the step point on thehinge.) Use either the bench vise or the vise grip to hold bracket andgrid it. I cant express enough how important that you shape and grindthe bracket exactly to the shape of the original hinge. I didnt grindthe arm until I was into the next step.

HP DV9000 laptop hinges

LCD hinges For DV9000 AT9A-R AT9A-L laptop Notebook 17"
This fix worked for Part Number
3JAT9HATP21 HINGE-L(JAR), 3KAT9HATP22 HINGE-R(JAR), 432963-001, 432964-001, AT9A-SZS-L 3KAT9HATP06, AT9A-SZS-L 3KAT9HATP22, AT9A-SZS-R 3JAT9HATP05, AT9A-SZS-R 3KAT9HATP21
Compatible HP DV9000 series Models
DV9000 series, DV9000T, DV9000Z, DV9005, DV9009, DV9010, DV9023, DV9030, DV9040, DV9060, DV9200 series, DV9205, DV9207, DV9210, DV9220, DV9225, DV9230, DV9260, DV9300 series, DV9310, DV9320, DV9330, DV9334, DV9339

There are a few steps here that arecritical that they are done correctly or the LCD screen wont fit back into thecase chassis

step 1

You must remove the 3 little rubber screw covers located on the top edgeof the laptop screen at the right, center & left side using the mini flat head screwdriver. Then remove the 3 screws located under the rubber covers.

step 2
Then you must remove the outer screen bezel, which unsnaps. Be verycareful not to force the plastic for it may crack! I would start from theleft hinge corner which is probably open, working clockwise with the littleflat head screwdriver prying it apart every inch or so. You may also haveto remove the bottom right andl eft rubber screw covers and remove those screws as well to free the bezel.

step 3
Now that the LCD is fully exposed you can see how destroyed the hingeand assembly points are damaged DUE TO POOR CONSTRUCTION BY THE MANUFACTURER'S DESIGN!

step 4
Then you must unscrew the 2 very small screws that are on the left hingeconnecting to the LCD screen. Now take notice how much space is betweenthe bottom of the LCD screen and the left hinge assembly. For this is oneof the things that can make this repair render your efforts useless whenyou try to reassemble! There is only about 1/16" clearance.

LCD Inverter For GATEWAY 7000 Series

Replacement Laptop LCD Inverter For GATEWAY 7000 Series

Gateway W720 MX7000 7000 M520 GZ G LCD inverter
Change the high pressure plank is relatively a matter which bothers, had better seek a professional to replace because of taking a dissimilarity of have the high pressure and circuit arrange.
It can solve following problem:
the picture that can ambiguously see up the LCD in the bright place,
the light tube has already can't drive
Each inverter is tested before shipping and are 100% working.
Compatible GATEWAY Part Number and Models
Part Number :
100375, 293348-001, 83-120002-000G, 83-120062-3000, 83-1200623, 83-120063-3000, 83-120082-3000, 83-120082-300G, 83-120085-3000, B1425050G00004, LG LP150X08(A3), LTN154X1-L03, MPT N052, MPT N0950806, MPTN095, T27I041.00, W720
Fit Model:
7110GX, 7210, 7210GX, 7215, 7215GX, 7305, 7305GZ, 7320, 7320GZ, 7322, 7322GZ,
7330GZ, 7405, 7405GX, 7410, 7410GX, 7415, 7415GX, 7422, 7422GX, 7426, 7426GX, 7508, 7508GX, 7510, 7510GX ,M520 Series,MX7000 Series, MX7118, MX7337, MX7340, MX7515, MX7525....
Compatible EMACHINES Part Number and Models:
Compatible Code
W720, 83-120082-3000, 83-120082-300G, 83-120002-000G, 83-120062-3000, 83-120063-3000, 83-120085-3000, T27I041.00,293348-001, 83-1200623, 100375, B1425050G00004, MPTN095, MPT N052 ,MPT N0950806,LG LP150X08(A3), LTN154X1-L03

Fit Model
M2000 Series, M5000 Series, M6000 Series

Compatible COMPAQ Part Number and Models
Compatible Code:
W720, T27I041.00,83-120082-3000, 83-120082-300G, 83-120002-000G, 83-120062-3000, 83-120063-3000, 83-120085-3000, 293348-001, 83-1200623, 100375, B1425050G00004, MPTN095, MPT N052, MPT N0950806, LG LP150X08(A3), LTN154X1-L03
Fit Model:
Presario 900 series, Presario 1500 series, EVO N1000c series, EVO N1000v series,EVO N1015v series, EVO N1020v series

SAMSUNG BST3438SC

SAMSUNG BST3438SC Rechargeable replacement mobile phone battery (Li-ion)

Features:Japan or Korea made grade A cells, Built-in rechargeable battery protection circuit, Strict Li-ion battery circuit management, 100% compatible with original equipment Li-ion chargers, Lithium Ion rechargeable SAMSUNG BST3438SC battery, no memory effect and environment friendly, 100% OEM compatible and stable performance, Certification: CE, CCC ,ISO9001,UL,CUL.

Descirption:SAMSUNG BST3438SC Mobile Phone Battery, Battery Chemistry: Li-ion, Battery Voltage: 3.70V, Capacity: 900mAh, Dimension: 66.95 x 43.95 x 7.40 mm, Weight: 25.00 g

Compatible Battery Code:BST3438SC , BST3438SEC/STD , CCR040SBEC/STD

Fits Models:SGH-E620 , SGH-E628

Other Mobile Phone Battery
SAMSUNG SGH-E500 mobile phone battery
NOKIA 3109 Classic mobile phone battery
High quality NOKIA 1265, 1325, 1508i, 2650, 2651, 2652, 2865, 3108, 3500 classic, 5100mobile phone battery